Autel IM608 Cayenne Kessy Lost Communication Solution

 Problem: Today i try to add a key to a Porsche Cayenne 2008 with Autel IM608.

Read data from ecu me7 -ok
7th bytes from working key – ok
Make dealer key – ok
Program key – no ok
Lost communication with car when i want to program.
The original key can always start the car. Any solution?

 

 

Possible solutions:

Solution 1)
Just went through this a couple days ago. I had to jump fuse 26 and 36 to wake up car gateway aka cluster and then used VVDI2 to do key learn with pin I got from Autel, because Autel kept losing communication, if you go under diagnostic and talk to Kessy you’ll see it talks just fine but some glitch in the learning process.

just put power to the car normally and then jump the power from a full time fuse like 36 to the one that needs to be powered up 26.

You might be able to do it through diagnostic mode using same instructions as vcds and a PIN code like you would with earlier Volkswagens.

Solution 2:

the solution was to pull kessy and eeprom it then make key on bench.. ended up being quicker than trying to add the key obd2.

Autel XP400 Read Write flash ST 29F400BB

 Read and Write flash Magnet Marelli ST 29F400BB with autel xp400 pro. the adapters are from the IMPKA set.

Autel IM508 Program Subaru BRZ 2013 All Keys Lost

 Subaru BRZ 2013 proximity all keys lost is done with Autel IM508 XP400 Pro.

Get Denso ECU box out, unsolder the chip, read eeprom 93C86, solder back, connect Denso back, use autel im508 with apb112 to create analog key then add smart keyless.

Using after-market key.

Definitely saved a customer 2k$ because the dealer charges 2800 to replace key + smart box + engine ECU.

http://www.key-programmer.org/2022/10/19/autel-im508-program-subaru-brz-2013-all-smart-keys-lost/

Autel IM508 Bricks Nissan Rogue 2017?

 This is a Nissan Rogue 2017. Just added a spare proximity key with Autel IM508 but bricked it.  Pushing start does nothing. VIN is NA when scanning ships ecu and ECU NA. BCM is fine. When read pin everything went dead. BCM I have is not on the bad list. Any solution?

Solution:

You did not brick the BCM. Long battery reset, VIN number will come back in a few minutes.

Battery reset and test, disconnect both terminals, leave for 15-20 minutes and re connect, re-scan to test.

If the BCM went to sleep on you, try disconnecting both battery terminals and touch them both together for few minutes, if that doesn’t work try leaving both battery terminals disconnected for about 45 minutes.

 

Feedback:

45 minutes worked with key pressed to start afterwards and held and had to reprogram original key of course.  I have managed to successfully get the job done with im508.

Program Kia Forte 2018 4D60 All Keys Lost with Autel IM608

 I have encountered real trouble many times but I haven’t found proper information online. I did today a key for a Kia Forte 2018. It is an 80bit chip, so there is not a lot of information out there for it. But here’s the thing i did it with the Xhorse vvdi key tool max here.

 

I will show you how I managed to do it.  First of all I used my Autel im608 to receive vehicle information and i see that it is a 4D60 80bit chip.

In the Xhorse I went to generate transponder and I couldn’t find that chip. But there is an 80bit option between ID70-ID83 (80bits)

I went here and at the bottom here you have here 4d70 Hyundai Kia (80bit) even though this one is 4D60. I try to make this transponder into this chip here with vvdi super chip xt27. It worked and it programmed.

It is successfully programmed with im608.  If you will ever need kia fortes this is the key.

Hope I managed to help you guys.

Autel IM608 Program Toyota Yaris 2019 All Key Lost

 Toyota yaris 2019 hybrid all keys lost situation. Autel IM608 Haven’t able to read backup over obd without any key, also g-box wires picture is different. Inside box is 8 leg chip 93c86, read it and make apa112 and program keys done.

without key autel haven’t be able to read eeprom and g-box wires was working because of different box, now the job is ready.

Inside box was 86 chip have remove and made backup and apa112 it take over

Have to use xhorse universal toyota key xm38

Autel IM608 Program Renault Kadjar 2022 Smart Card

 Autel IM608 successfully added a smart card to a Renault Kadjar 2022. IM608 warn me to erase all keys Autel He himself said it was a risk.

No need gateway. Obd2 direct All by obd2. Read flash data, make dealer key and learn key.

Good internet. Power supply 3 minutes job done.

Βefore proceeding with the < add > procedure on the RENAULT KADJAR:- it would be good to check the emergency procedure – We must remove the battery from the card and check, if the car (the antenna) reads the chip completely. if this is not done, in the process of deleting and adding keys – the car will not be able to read the keys.