Tuesday, September 11, 2018

Auro Otosys IM100 Register Nissan Rogue 2016 Key

(11-09-2018) The newest Auro Otosys IM100 test is done by obdii365.com.
The test report… Here you go.

Key programming tool: OtoSys IM100
Function to test: Register a new key
auro-otosys-im100-nissan-rogue-1

Car: 2016 Nissan Rogue

auro-otosys-im100-nissan-rogue-2

Connection: through OBD

The procedure:
Connection is done!
Otosys IM100 starts and select the car: 2016 Nissan Rogue
auro-otosys-im100-nissan-rogue-3
auro-otosys-im100-nissan-rogue-4

auro-otosys-im100-nissan-rogue-5
auro-otosys-im100-nissan-rogue-6

auro-otosys-im100-nissan-rogue-7

auro-otosys-im100-nissan-rogue-8

auro-otosys-im100-nissan-rogue-9
Note:Here, select 2017 and up even though it was a 2016
Go to the Immobilizer/Smart system to register a key
auro-otosys-im100-nissan-rogue-10
auro-otosys-im100-nissan-rogue-11

auro-otosys-im100-nissan-rogue-12
VERY IMPRORTANT: with all late model Rogues and all programmers there is a risk of bricking the car
AURO OtoSys IM100 is gonna to register a key:
Set the vehicle to the following status and then touch OK
– ignition switch or power switch: LOCK
– hazard switch: ON (for preventing BCM from entering into CAN communication sleep mode)
– P (A/T) or neutral (M/T)
– battery voltage: more than 12.5 volts
– steering: not in fully locked

Register an intelligent key
Operate according the following procedures
  1. Press push button ignition switch once; check that indicator on push-button ignition switch blinks
  2. Contact the intelligent key to push-button ignition switch within 5 seconds. Check that buzzer in combination meter sounds twice
Caution: contact the logo of the intelligent key to the center of the ignition switch
  1. Check that turn ignition switch changes automatically to the ON position and that security indicator blinks for 5 times. Check that push-button ignition turns ON.
  2. Turn ignition switch to the OFF position. Wait for 5 seconds or more
  3. A maximum of 4 intelligent keys can be registered by repeating procedures from step 1. touch Next to end key registration mode.

auro-otosys-im100-nissan-rogue-14

auro-otosys-im100-nissan-rogue-15

auro-otosys-im100-nissan-rogue-16

auro-otosys-im100-nissan-rogue-17

auro-otosys-im100-nissan-rogue-18

auro-otosys-im100-nissan-rogue-19

auro-otosys-im100-nissan-rogue-20
auro-otosys-im100-nissan-rogue-21
auro-otosys-im100-nissan-rogue-22
After key registration, the system returns to key registration mode. Therefore, it is necessary to end operation. Operate according to the following procedures.
  1. Press push button ignition switch once; check that indicator on push-button ignition switch blinks
  2. Contact the registered intelligent key to push-button ignition switch within 5 seconds. A buzzer in combination meter sounds for 2 seconds
Caution: contact the logo of the intelligent key to the center of the ignition switch
  1. Turn ignition switch to the OFF position. Wait for 5 seconds or more
  2. Check that the key warning lamp blinks for 5 times when driver door is opened or closed
  3. Check that security indicator blinks at internals of appox 3seconds while ignition switch is in the OFF position
  4. Operate registered intelligent key out of the vehicle. Check that doors lock and unlock. This status indicates that key registration mode ends

auro-otosys-im100-nissan-rogue-23

Check the following items using all registered keys.
  1. Put intelligent key in the vehicle (within the inside key antenna detection area). check that push-button ignition switch can change the ignition switch position and that it can start engine
  2. Put the intelligent key out of the vehicle (out of the inside key antenna detection area). check that the ignition switch cannot be changed using push-button ignition switch
  3. After completing above confirmation operation touch End.

auro-otosys-im100-nissan-rogue-24

Done!

No comments:

Post a Comment